social

Adjusting the Feed Dog Height on a Janome HD 3000?

Adjusting the Feed Dog Height on a Janome HD 3000 - manual pageI have a Janome HD 3000 and I need to adjust the height of the feed dog. I think there is an error in the service manual on the internet, because for the setscrew (A) there is no way to loosen it and I guess it confuses (A) and (B) in the diagram attached?

Advertisement


Could you let me know the correct procedure to avoid breaking everything.

Thank you.

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!


Gold Post Medal for All Time! 677 Posts
October 29, 20190 found this helpful

I would contact customer service at Janome.com. Upload a picture of your machine, too.

Reply Was this helpful? Yes

Bronze Post Medal for All Time! 105 Posts
October 30, 20190 found this helpful

Actually that is the correct screw to use to adjust the feed dog of the machine. If the screw is not moving it is because it is already so tight it can not be screwed in tighter at all. If this is the issue and you are not being able to adjust it correctly there could be a problem with the screw being too tight or that it is rusted in place and can not move.

Advertisement

I would call the service department and talk with a rep there to ask for help. You may need to buy a new feed dog for the machine so you can adjust the foot on the machine so it feeds correctly for the material you are using.

Reply Was this helpful? Yes

Gold Feedback Medal for All Time! 949 Feedbacks
November 4, 20190 found this helpful

It seems you are referring to the information on page 17 of the Janome HD 3000 Servicing Manual (not the regular manual) and this manual is mostly used by repair shops so the language will usually be short and not much in explanations.
You will have to follow the limited instructions to the letter and it clearly states that after completing numbers 1, 2, and 3 to loosen setscrew (A) and then nut (B). then follow through to finish.

Advertisement

If your setscrew (A) is not turning then it may need a little sewing machine oil loosen the grip. That is probably all you need to do.

Here is a link if you wish to contact support at Janome but very likely they will direct you to the Janome sewing store in your area.

www.janome.com/.../

Reply Was this helpful? Yes
Anonymous
November 5, 20190 found this helpful

Thanks but I tryied that and finaly a screwdriver a little be to large and a few tiks of a hamer and some swet and I finely succeded

Thanks to all of you.

Reply Was this helpful? Yes

Gold Feedback Medal for All Time! 949 Feedbacks
November 6, 20190 found this helpful

Thanks for letting us know.
We're always glad to hear how problems were solved successfully.

Reply Was this helpful? Yes
Advertisement

Add your voice! Click below to answer. ThriftyFun is powered by your wisdom!

In This Page
Categories
Home and Garden Repair Machines Sewing MachinesOctober 29, 2019
Pages
More
🍂
Thanksgiving Ideas!
🎃
Halloween Ideas!
Facebook
Pinterest
YouTube
Instagram
Contests!
Newsletters
Ask a Question
Share a Post
Categories
Better LivingBudget & FinanceBusiness and LegalComputersConsumer AdviceCoronavirusCraftsEducationEntertainmentFood and RecipesHealth & BeautyHolidays and PartiesHome and GardenMake Your OwnOrganizingParentingPetsPhotosTravel and RecreationWeddings
Published by ThriftyFun.
Desktop Page | View Mobile
Disclaimer | Privacy Policy | Contact Us
Generated 2022-10-25 11:39:52 in 1 secs. ⛅️️
© 1997-2022 by Cumuli, Inc. All Rights Reserved.
https://www.thriftyfun.com/Adjusting-the-Feed-Dog-Height-on-a-Janome-HD-3000.html