Painting Cultured Marble?

I know this is an old post but I learned some of the stuff below on this site and wanted to share .....

Before I start with what I did I want to say that I had my hubby remove the faucet because the one I had was icky.
I bought a new one at home depot that is beautiful for 16 bucks. They were on sale!
This made it a lot easier to get a solid coat of primer over everything.
Also I used a grey primer because I did not want a solid tan paint on the top .. the variation with the grey and the tan with black flecks is very nice.

Here is the materials list that I used.
Sand paper - I used a medium grit sand paper. The purpose is to get the sheen off and get the surface ready to accept the paint.
Primer - I used Glidden Gripper Grey Primer for Superior Deep color Result (per the label) For the counter and Kilz spray for the sink in white.
Spray stone - I used Rust-Oleum American Accents Stone in Sienna Stone. It looked a little pinkish on the cap but when you put it over grey its beautiful.
Envirotex - This is a name brand for a polymer resin. Which is like putting 50 coats of polyurethane on at once.. It give a great shine as you can see in gator girls work.
Paint roller - I have a small foam roller that I use for all my little projects that works great.
Paint brush - Any will do really. I used it to get the "nooks and crannys"

Tape - Painters tape or masking tape to tape edges of counter and to make the line in the sink.
Disposable cups - use to pour the envirotex down the backsplash.
Paint spreader - kinda like a big putty knife. I bought a wide one and a not so wide one. I smoothed the edges down on the smaller one to create a kinda rounded edge for getting in the curves of the shell sink.

Now most of these can be purchased at home depot or lowes even walmart.(where I got most of my stuff)
However the envirotex can usually be picked up at a craft store like Michaels, Joanns, and Hobby Lobby. Its realatively inexpensive ranging from 9-30 dollars depending on the amount you are getting.

Step 1.
Clean your surface of any debris and sand well. If you own a belt sander its what I used for the flat surfaces and did the rest by hand.

Step 2.
Wipe all the dust off from the sanding.
Step 3.
With trial and error I have found that painting the sink white first is easiest and gives the best results.
Don't worry about taping the sink yet.. just spray the Kilz white spray paint evenly over the entire sink area getting an even coat.
To avoid drips dont get to close to the surface. If you do get drips.. wipe the excess and let it dry and sand and reapply if necessary. Let it dry.
Step 4.
Tape the sink about a 1/4 the way down and tape paper to the bottom so the sink is completely covered with the exception of the "rim"
Step 5.
Prime the entire counter top using your foam roller and brush with the Glidden Gripper. Let it dry. Follow Basic instructions on the Glidden can.
Step 6.
Spray the Rust-Oleum over the entire counter to get the desired color/coverage. This is the point that you would add the glitter for the sparkle if you so desire. Let it dry
Step 7.
Follow the instructions on the envirotex. Stir very well. If you don't you can end up with soft spots that won't dry.
Step 8.
Start envirotexing your counter by working from the top down.. What I mean is start with the back splash and work your way down to the sink.
Pour some envirotex into one of the disposable cups and slowly start pouring down the back splash. Use your paint spreader to "scoop" the puddles back up.
Do this a few times to get the stuff to stick.
Then pour some on the counter and start working it around saving the sink for last.
Don't for get to clean up your edges under the counter with a foam brush.
To get the envirotex down the sink use the same method as with the backsplash.
Let it all cure per the manufacturers lable