Appliances (Questions)Ask a Question

Follow

Unanswered Questions

These questions don't have answers yet. Can you help them out? ThriftyFun is powered by your wisdom.

Troubleshooting Singer Steam Press?Hi, I have a singer ESP-2 Steam press and the issue I have is when it's plugged in with the power button off, the screen is still lightly illuminated. Is it something I should be worried about? It's not even a year old.

 

Answer

Washer Won't Drain?I have a LG top load washer. It is a little over a year old. My washer is running through the the wash cycle, but won't drain. It sounds like it's sucking water and a little comes out but then it stops and reads OE code.

 

Answer

Repairing a Chest Freezer Thermostat Probe?I have a Frigidaire chest freezer. How do I remove the thermostat probe?

 

Answer

Kenmore Refrigerator Leaking?My Kenmore ice box is leaking. How do I remove the inside panel?

 

Answer

In-Door Ice Maker Not Working?I just purchased a new Kenmore Elite side by side 30 cu ft refrigerator freezer. I have water in the door, but the ice maker will not work. The water dispenser works. My old Kenmore made ice on the same connection.

 

Answer

Maytag Washer Error Codes?What is F-54?

 

Answer

Browse Questions

Sealing Sensor Light Does Not Work?Is there a way to replace the red, yellow, and blue sensor/seal light? I can manually seal bags but only the red seal light comes on when I press "Seal". There are no lights to indicate if the air is being removed.

 

1 AnswerAnswer

Hoover Power Pro XL Leaking?I had just fixed the belt on my Hoover carpet cleaner. It had worked perfectly fine with the hose but it wasn't working as a regular carpet cleaner obviously because the belt was broken. I took it apart, put the new belt on and all the sudden now the water completely comes out within a minute onto the floor. I didn't even press the handle or anything, it just came out and it did suck the water back up but there was a long thick plastic piece that I could not find where it would go. I have searched YouTube and could not figure out where this piece would have went.

 

6 AnswersAnswer

Chefmate Error Code E:03?Needed a second bread machine. Bought a used Chefmate HB-215. It keeps showing error code E:03 every time you try to set anything that reading comes up. Anyone familiar with what it means?

 

6 AnswersAnswer

Sunbeam Breadmaker Is Not Kneading?My Sunbeam breadmaker is not kneading, what do I do?

 

5 AnswersAnswer

Swiffer Wet Jet Not Working?My swiffer Wet jet lights come on but motor will not, batteries are fine!

 

5 AnswersAnswer

Fixing a Frigidaire Dishwasher?The start button on my Frigidaire LFID2426TF2A dishwasher has intermittently stopped working. The other buttons are working fine but the start button continues to flash, no matter how many times I press it. Then, out of the blue, I will try again and it works. I am guessing there must be a bad connection. Does anyone know how to repair this? Is it worth repairing?

 

3 AnswersAnswer

Welbilt Bread Machine Not Baking?I'm not sure what's going on with my bread machine. In the past when the bread didn't rise enough, I assumed I was doing something wrong. This time, it not only didn't rise much, but the bread is not cooked enough. The paddle also baked into the bread. All the ingredients were fresh, though I did change the order I added them. Could that have caused the problem, or is there something wrong with the machine?

 

5 AnswersAnswer

Looking for a Bread Maker Motor?I have a KBS 2 lbs bread maker and it has began slowing down and not kneading as it used to. I'd like to replace the motor to see if that resolves the issue. It does function once it breaks through the dough, but will stall out often and appears to be whining to get past that point.

 

5 AnswersAnswer

Kenmore Fridge Not Cool Yet?I have a Kenmore fridge that hasn't been used in 3 years. I plugged it in last night around 7 and woke up today and it's still not cool. How long would it usually take after being unplugged that long. I bought it brand new 4 years ago and used it for a year before it was unplugged. So it's pretty new.

 

6 AnswersAnswer

Dishwasher Will Not Start?I have a Frigidaire Gallery dishwasher. 2 years old rarely used. When I run a load it will always flash "Close Door" then begins to fill with water. It does neither but all the lights light. I'm about to order a water inlet valve. However it is rather pricey and I'm not sure if it's going to resolve the problem. Why does it flash, close door?

 

6 AnswersAnswer

Troubleshooting a Black and Decker Breadmaker?Used my Black and Decker All-in-one Breadmaker B1561 extensively during Covid, but recently the bread rose, then sank in the later stages. The pan paddle seems very stiff and I find the machine paddle stiff also. Could this be the problem?

 

6 AnswersAnswer

Repairing a Breville Breadmaker?I have a Breville breadmaker model BR7L.The heating element is defunct. I have been unable to find a site which allows me to purchase a replacement. Can you please advise me of an appropriate site?

 

3 AnswersAnswer

Kenmore Ice Maker to Crush Ice?I was just wondering if a regular Kenmore refrigerator with an inside half moon shaped ice cube maker can be converted to make crushed ice instead of what it does now? Thanks!

 

5 AnswersAnswer

Replacement Purple Battery Holder for Swiffer Wet Jet?Where can I find a replacement battery holder for Swiffer Wet Jet, purple?

 

9 AnswersAnswer

Washing Machine Making a Loud Noise?My washing machine started making a loud noise when it spins. It is a Whirlpool top-loading washer, model number WTW4816FW2. It is a loud rubbing sound. Does anyone know how to fix this?

 

9 AnswersAnswer

Is it Worth Trying to Repair a Bread Machine?I got this old bread machine Regal Pro Breadmaker K6773. It works when I plug it in, but when I try to set a mode or do anything else, I get this E 07 Error, which, according to the manual, is a "possible circuitry defect". Is there any way to find out what exactly is wrong with it or, more importantly, is there any way to fix it?

 

5 AnswersAnswer

Repairing a Hitachi Bread Machine?My Hitachi Bread Machine (HB-B301) is over 20 years old. When I attempted to use it, I received an error message (--P): (1) an excessive amount of flour as compared to water. (2) An insufficient amount of water as compared to flour. (3) The seal packing is scratched.. (Ingredients block the lubricant oil between the shaft and metal of the bread pan because of the leakage of ingredients through seal packing.)

 

4 AnswersAnswer

H2O HD Repair?Does anyone know the size of the security screwdriver required for an H2O HD steamer mop? Thanks.

 

4 AnswersAnswer

Repairing Corningware Coffee Maker?Has anyone found a food safe adhesive to reattach the steel collar that actually works? Thanks!

 

11 AnswersAnswer

Replacement Parts for George Foreman?Where can I find a replacement drip tray P/N21678 for a George Foreman Lean-Mean Contact Roasting Machine (GV&)?

 

4 AnswersAnswer

Repairing a Steam Mop?Thane H2O X5 steam mop. The tubing inside the unit has split. I need to know the type and size of tubing to be able to replace it. Thane just tells me I need to buy a replacement mop. Not an option.

 

4 AnswersAnswer

Repairing Control Panel of Breadmaker?The control panel buttons on my Cookworks breadmaker do not respond anymore when pressed. How can I repair it? Can it be replaced? The machine itself worked fine.

 

2 AnswersAnswer

GE Washer Drains But Won't Spin?I have a front load washer that won't spin. I've replaced the door switch, checked the filter, pulled the boot, and lines. It has a stater and I've inspected it, what am I missing? Any help would be appreciated.

 

3 AnswersAnswer

Microwave Plate Repair/Replacement?My microwave plate is broken. Can't I just use a Melmac, plastic, or glass plate and drill in 3 plastic inserts that are cut just long enough to allow the plate to be turned? I'm trying to be creative and save 30.00.

 

8 AnswersAnswer

George Foreman Heating ElementI have a George Foreman 10040 and need a heating element.

 

3 AnswersAnswer

Repairing an Oster Bread MakerI have an Oster 5858 bread maker. The shaft that holds the paddle falls out of the bowl base bottom. I have to keep the bowl base with the shaft locked in the breadmaker, then attach the paddle so that I can fill the bowl with liquids and then the dry ingredients. The shaft does sits slightly lower, but still works with the paddle. The bread maker still does a good job of mixing the dough.

 

6 AnswersAnswer

Repairing a Zojirushi Bread Maker?I have had a Zojirushi breadmaker, model BB-CEC20 for about 7 years, but only started using it more frequently recently, so it hasn't gotten a whole lot of use. Yesterday, it turned off mid-cycle (after the bread rose) and now I can't get it to turn on again. There's no response pressing any of the buttons on the control panel.

 

2 AnswersAnswer

Descaling a Steam Pro Press 26?'This steam press is not working properly, due to water dripping from steam holes. I checked everything and know it needs descaling. How do I do that?

 

1 AnswerAnswer

Bread Pan and Paddle for Black and DeckerPaddle is rubbing and squeaking while the bottom apparatus that the paddle fits on is leaking black matter under the pan. It looks like melting rubber.

 

3 AnswersAnswer

Rocket Chef Blade Replacement?How do you change blades on the Rocket Chef? Mine seems to be stuck and I can't get it out.

 

5 AnswersAnswer

Shafts in Bread Machine Fell Out?The shafts in my Black & Decker bread maker fell out and all my liquids spilled out. Is there something to keep them attached to the bread pan?

 

2 AnswersAnswer

Kenmore Elite Fridge Not Cooling?The model number is 795.72489411 s, it is not cooling at all. I initially put it in and out of store/demo mode 5 times and it started working! It worked for 3 days perfectly and now won't do a thing :( The compressor does have a slight hum; no clicking noise. The fan on the back is running. Where do I go next? Repair won't be able to come out for 3 weeks!

 

6 AnswersAnswer

Repairing a Leaking H2O X5 Mop?My H2O X5 mop is leaking from the small hole at the bottom of the base handle, not from the head. It was dropped accidentally and now leaks. As you can see by the picture I put blue tack on it.'

 

6 AnswersAnswer

Repairing My Electric FanHelp! My stand fan base is always falling. How to fix it?

 

2 AnswersAnswer

Finding H20 Steam Mop PartMy H20 X5 steam mop stopped working. I took it apart and two of the pipes broke. I descaled the little boiler then got some more hose, unfortunately the first I purchased was too thick and couldn't close the unit. The next I got just melted, grrr. Where can I buy some more hose from that will fit and not melt please?

 

5 AnswersAnswer

Repairing the Latch on a Hoover Carpet Cleaner?How do I reattach the cleaning access latch?

 

4 AnswersAnswer

Adjusting the Hinge on a Kenmore Elite Microwave?I have a Kenmore Elite microwave-convection oven combo, model# 790.48903000. The hinges are on the bottom and the latches are on the top. The left latch suddenly will not line up into the hole it's supposed to fit. The door will not close because of it. The right latch still lines up fine as far as I can tell.

 

3 AnswersAnswer

Parts for a Welbuilt Bread Machine?I have a Welbuilt bread maker Model ABM3300. I need to replace all of the moving parts at the bottom of the bread pan, or perhaps an intact functioning bread pan.

 

3 AnswersAnswer

Repairing a Loose Microwave Door that Won't Open?I have a Whirlpool microwave oven, model WMC50522AS1. The door will not open when I pushed the button, I have to manually lift the door up a little bit and then the door will pop open. When the door is open, I hold the door and I can feel that the door is loose. Do we have a way to tight it up?

 

1 AnswerAnswer

Samsung Dispenses Water Instead of Ice?My Samsung refrigerator model RF4287 will not dispense ice. It is still making ice, but it dispenses water instead when you push the ice dispenser lever.

 

3 AnswersAnswer

Sunbeam Bread Machine Won't Stop Running?I have a Sunbeam bread machine, model 5891 that as soon as you plug it in it starts running. I have tried to reset it by holding in on the power button, but it won't stop unless I unplug it.

 

5 AnswersAnswer

Kenmore Ice Maker Is Making Less Ice?My Kenmore ice maker is making ice, but not as much as it used to produce. The ice maker keeps making knocking sounds. I changed the flyer, but the sounds still continue.

 

4 AnswersAnswer

Repairing a Morphy Richards 48268 Bread MakerMy Morphy Richards 48268 bread maker was working perfectly. Then this morning there was a rattling sound from the motor area and the paddle and the shaft were not turning.

 

5 AnswersAnswer

Small Pieces of Rubber Found in Maytag A9400 Washing Machine?My Maytag top loading washing machine leaves small pieces of rubber in the tub after the washer has finished spinning and the washing is done. It leaves a very small amount of rubber no matter what I am washing. What is the reason for the rubber and what do I need to do to correct this problem? The washing machine does not make any unusual noises or behave in an abnormal way.

 

3 AnswersAnswer

When Is detergent Cup Supposed to Open?I have an older GE dishwasher. I am sure it is not worth it to get a repair done. The detergent cup is not opening, it is not blocked and there is no residue gumming up the works. I would like to know when it is supposed to open so I can watch for the right cycle and manually intervene :)

 

5 AnswersAnswer

Welbilt Bread Machine Error Codes?As I tried to start my Welbilt bread machine after adding all the ingredients I got an error that said HI. I suspect it's related to the temperature of the water which had gotten a little more than warm (boiling). I can't find this code. It's working now so maybe it cooled down.

 

4 AnswersAnswer

Ice Maker Overflows When Dispensing Water?I just changed the valve on my Whirlpool gs6haxls03 fridge because the ice maker was not working. Now every time the drinking water paddle is pushed it dispenses water into the ice tray and overflows into the freezer.

 

3 AnswersAnswer

Ice Clumping in Kenmore Refrigerator Ice Bin?I have Kenmore French door refrigerator. The ice maker is in refrigerator and makes ice great except the ice clumps in tray. There are no visible leaks. It seems to clump in the center of the bin. Could this be a defrost terminator (thermostat) issue? I tried adjusting template up and down. No change. I replaced the water valve in back of the unit. No change; it was still clumping ice.

 

3 AnswersAnswer

Bread Maker Paddle Remains Stuck in Finished Bread?I love my breadmaker and the bread releases easily once baked. No sticking, but the paddle remains in the bread and I have to dig it out. Any suggestions?

 

3 AnswersAnswer

Sanyo Bread Maker Doesn't Start?At this time of COVID, I decided to get out my Sanyo bread maker. It had not been used for several years. I put all the ingredients in pan and clicked it in place. The numbers lit up once it was plugged in. I pressed my bread number and start, but nothing happens. The time shows in the lighted window, but no action.

 

1 AnswerAnswer

Breadman TR 444 Stops Mid Process?My Breadman Tr444 works most of the time OK. But it seems to be shutting down mid processing more often. It goes thru kneading and then just stops. The panel just displays as if it was preselection. There is no heat error message.

 

6 AnswersAnswer

Scunci Steamer Switch On All of the Time?I have had my steamer for years and love it, but lately it wouldn't steam so my husband took it apart and did what was suggested. Now if just steams all the time without having the button on the handle depressed. So it runs out of steam way too quickly and doesn't seem to have the force it used to have.

 

4 AnswersAnswer

Wolfgang Puck Bread Machine Trips GFI Switch?My Wolfgang Puck bread maker keeps tripping the GFI switch when it goes into the baking mode. Is this an easy fix?

 

3 AnswersAnswer

Repairing an Oster Bread Maker?I have an Oster bread machine that is stuck in one mode. How can I fix it?

 

6 AnswersAnswer

Mister Coffee Bread Machine Not Working?I have a Mr. Coffee BMR200 bread machine. The initial knead cycle works then it just starts spinning and spinning really fast and won't stop. How can I fix this?

 

2 AnswersAnswer

Repairing a Bread Machine?I have a Zojirushi bbccx20 bread machine. The pan seems to have an issue. One paddle is very hard to turn, the other moves smoothly. Is it possible to fix?

 

4 AnswersAnswer

Bread Maker Won't Knead the Dough?Have a Sunbeam 5891 breadmaker that suddenly refuses to knead the dough. The machine runs, but the paddle won't turn. Does it need a new basket and paddle or a good swift chunk into the trash? I can't find a bread machine anywhere on line and my handmade bread sucks rocks.

 

3 AnswersAnswer

Electric Ice Cream Maker Not Working?Why doesn't my electric ice cream maker turn at all? I hear the motor running. What am I doing wrong? Does it take a minute to warm up?

 

3 AnswersAnswer

Handle on Hoover Carpet Cleaner Won't Lock in Place?My Hoover dual power pet max shampooer handle will not stay upright or lock into place. It's like a piece is missing? I don't want to have to spend hours on the phone if it's not something I can fix. Has anyone had this problem?

 

19 AnswersAnswer

Singer Steam Press Won't Steam?I have a Singer steam press table top presser. The dry iron does work, the steam does not. Any ideas how to fix that?

 

4 AnswersAnswer

Repairing a Kenmore Ice Maker?I have a Kenmore model #106.57368700. The ice maker was leaking and causing big a chunk to form in the ice bin. We replaced the water inlet valve, but that did not work so we replaced the ice maker. Now the water will not shut off. Any idea what need to do I need to do to fix it?

 

4 AnswersAnswer

Repairing a Kenmore Elite Ice Maker?I have a 7-year old Kenmore Elite side-by-side refrigerator 795.5137. Ice is being made, the ice maker auger turns, but the flap does not open. The flap motor was not running so I replaced it, but the new one isn't running either. Any thoughts?

 

1 AnswerAnswer

Panasonic Automatic Bread Maker Won't Turn On?We have a Panasonic bread maker that won't switch on. I have replaced the fuse, but it still doesn't work. I only used it 2 days ago when it was perfectly fine! Any ideas on what the problem might be? It is only 18 months old.

 

6 AnswersAnswer

Kenmore Refrigerator and Freezer Not Cooling Properly?I have a Kenmore refrigerator, model number 2537889. The freezer is cool, but starting to melt. The refrigerator itself is cool to the touch. The compressor and fan are running. I cleaned the coils. Anyone have an idea what could be wrong?

 

3 AnswersAnswer

Hoover SpinScrub Leaking Water?My Hoover Spinscrub steamVac cleaner just started leaking water from the bottom. Even when my lever was not off (not squirting water) the water was still leaking from the device. When I was drying the carpet with the vacuum, it was still squirting water (which made drying it useless).

 

3 AnswersAnswer

Kenmore Elite Not Spinning the Water Out?My Kenmore Elite top loader leaves my clothes still wet. How can I fix this?

 

5 AnswersAnswer

Repairing a Singer MSP 2 Steam Press?Suddenly the arm can not be pulled down during use or to lock. Can I repair this? It is a Singer MSP 2.

 

1 AnswerAnswer

My Bread Maker Isn't Mixing Completely?I have been using my bread maker for years now and it is pretty old. I pulled out my bread maker after a few months and I decided to make banana bread. I saw that it was mixing and all so I thought it was fine. After the baking cycle when I went to pull it out I noticed that the top half didn't even mix and only the bottom mixed and baked.

 

6 AnswersAnswer

Frigidaire Refrigerator Ice Maker Not Working?Our Frigidaire mf12269drm01 refrigerator worked perfectly till we added RO under the sink. We removed the filter and installed a bypass plug. Water from the door flows good and cold. However the ice maker stopped working altogether.

 

3 AnswersAnswer

Kenmore Top Freezer Section Not Working?I have a side by side Kenmore refrigerator. I don't know how old it is. I bought it second hand. The freezer on the bottom freezes, but top won't. I took off the panel inside and the fan up there is not working. Does it mean it needs a new fan? I am on a fixed income. I guess my question is could that be the problem how do I fix it and where do I go for parts.

 

6 AnswersAnswer

Breville Br1 Breadmaster Bread Machine Won't Heat Up?I have a Breville BR1 fan assisted bread maker. Recently I found that it doesn't heat up anymore. The dough is made perfectly. How do I open and repair it? Where do I buy the heating element?

 

3 AnswersAnswer

Hoover Steam Vac Leaking?My Hoover steam vac, F7452-900, All Terrain Spinbrush, is leaking from the solution/water tank. I need to know how to fix it.

 

1 AnswerAnswer

Display on Oster Bread Machine Not Working?My Oster bread machine has been working fine, but now the display does not show. It has power. It beeps, it kneads, and even bakes (per experiment), but I have no idea what cycle it's really on, which makes things a little tricky. Any idea if the display can be reset?

 

1 AnswerAnswer

Repairing a Bread Machine?My bread maker, a Breville BBM100, has destroyed part of its pan seal kit - a tiny washer that would fit on the end of my pinky finger. No spares are available. I've searched and now found there were never spares for this model, which they still make. Do you have any ideas about something I could use to improvise a repair? I've tried local suppliers of nut and bolts, etc. to no avail.

 

4 AnswersAnswer

Samsung Refrigerator Won't Dispense Ice?On my Samsung RF4287HARS refrigerator the "ice off" button is lit up. I press it and it will not go off. How do I get it to go off so that I can have ice once again?

 

1 AnswerAnswer

Top Half of Kenmore Side by Side Refrigerator Not Cold?I have a 19 year old Kenmore side by side refrigerator model #106.50559001. The top half on both sides will not get cold.

 

4 AnswersAnswer

Can't Open the Drip Tray on Food Saver?I have a Food Saver V4400 series vacuum sealer. I need an unusual repair. The sealer works great and it still seals very well. The problem is, I cannot open the pull out drip tray, it's closed tight and I cannot get it open. It is no longer under warranty so I cannot send it back to FoodSaver.

 

5 AnswersAnswer

Repairing a Russell Hobbs Bread Maker?Some kind person has donated a broken bread machine to a charity store instead of getting rid of it. My partner and I bought it and our excitement to bake has soured somewhat.

 

2 AnswersAnswer

Oven Temperature Gauge Not Working Properly?Oven temp gauge when preheating oven to 350 degrees takes about 5 minutes when it actually takes about thirty! Why is there about a 25 minute difference?

 

4 AnswersAnswer

Repairing an H20 Mop?The H20 Mop button no longer works. It will not turn off. What can I do to fix it or where can I send in for repairs?

 

5 AnswersAnswer

Repairing a Scunci Steamer?So I followed the suggestions and now the steamer works, but the handle got very hot. I need an oven mitt to hold it! I know that's not right and potentially dangerous. It was really hard to get the washers and nut back on the rod so I hope I don't have to do that part again!

 

2 AnswersAnswer

Repairing a Reliable Aria 350sp Steam Press?I am not getting steam on my Aria 350sp. Does anyone know a fix for this?

 

2 AnswersAnswer

Repairing a Galloping Gourmet Convention Oven?Is there a repair diagram for the motor and fan for the Galloping Gourmet convection oven? I have taken it apart to fix the broken bolt mounts, and I am having a hard time getting it back together.

 

2 AnswersAnswer

Hoover Pro Max Shampooer Leaking?My Hoover Pro Max 60 Model number FH50220 shampooer is leaking water. I fill it with clean water and detergent and it's empty in less than a minute. It's leaving water marks on my carpet because so much water leaks out.

 

6 AnswersAnswer

Refrigerator Water Filter Leaking?I recently replaced my Coldspot water filter and after doing so I drained about a gallon or two from water through the door. However, every time I get ice through the door, the water filter in the top of the fridge leaks inside the fridge.

 

3 AnswersAnswer

Refrigerator Not Cold Enough?I have a problem with my Kelvinator four door the fridge. It is not cold enough in a way some of the things get spoiled. My freezer is okay. What might be a problem?

 

3 AnswersAnswer

Ice Maker Only Dispenses Crushed Ice?My Kenmore side by side with the ice maker in the door dispenses crushed ice even when it's on cubed. It then clogs the shoot and nothing comes out.

 

7 AnswersAnswer

Replacing Timing Belt on a Bread Machine?I have a Wolfgang Puck bread machine that needs a new timing belt. How to I go about replacing it? Model BBME025

 

3 AnswersAnswer

Disassembling a Singer ESP2 Magic Steam Press?Does anybody have instructions or a manual in how to open up the ESP2 Magic Steam? I need to access the PCB and fix that as well as the metal plate (top). I opened a screw too far and the holder dropped.

 

7 AnswersAnswer

Repairing a Glass Cook Top?I had a cabinet door handle drop on the edge of my glass cooktop and put a bullseye type divot on the edge of the top. I'm wondering if there is anyway to repair, or fill-in, the divot. It is black glass still.

 

8 AnswersAnswer

Frigidaire Ice Maker Not Getting Water?I have a Frigidaire Gallery fridge. I have changed the water valve, filter, and the ice maker. It made only one round of ice and I can hear it trying to cycle, but no water goes into ice maker. I don't know what else I can do.

 

4 AnswersAnswer

Repairing a Hoover Smartwash Carpet Cleaner?I've had my machine for a year or better. I went to use it one day and the roller wouldn't roll and made this loud noise. It wasn't cleaning my carpet. We took it apart to check the belt and the belt is OK. So what could be the problem? I paid too much to just let it go.

 

4 AnswersAnswer

Mattress Pad Not Heating?My mattress pad is not heating properly. I have checked all the connections, and plug ins. Everything seems to working. Can you help?

 

7 AnswersAnswer

Electric Stove Burners Not Working Properly?My electric range only has one burner working properly. The other three burners can't work independently. I need to always turn on the good one to make other burners work.

 

4 AnswersAnswer

Cap Stuck on Scunci Pro Steamer?I have a Scunci Pro steamer model ps3888 and I can't unscrew the cap to add water.

 

1 AnswerAnswer

Bread Pan Stuck in Bread Maker?I recently purchased a second hand Kambrook bread maker from a friend. The bread pan is stuck inside the machine and cannot be removed, even with force. It looks to be in relatively good, clean condition. I am not sure how long since it has been used. Is this a common problem and what is the best way to remove it?

 

6 AnswersAnswer